Flaccid size

[Happy Toy]

My flaccid size increased from less then an inch to 3" completely flaccid (never any less), to 4" with 2 or 3 pumps, which is where I keep it most of the time. Before my implant I was 5.5" long erect with a 6.5" girth. I lost just over an inch of that girth with the implant and a 1/4" in length . I think the loss of girth was do to me using trimix injections for over 12 years. I notice the increase in girth over that time. I am thrilled with my flaccid size and very happy overall with my implant.

DSCN1699.JPG (137.14 KiB) Viewed 1871 times

DSCN1700.JPG (113.3 KiB) Viewed 1871 times

Pumped to max, 5.25" 5.25" girth

DSCN1688.JPG (197.86 KiB) Viewed 1871 times

[David_R]

Looks great, brother! (And an increase from less than 1 inch to 3 inches is pretty amazing, isn't it?)

[Smetro]

My flaccid size increased from less then an inch to 3" completely flaccid (never any less), to 4" with 2 or 3 pumps, which is where I keep it most of the time. Before my implant I was 5.5" long erect with a 6.5" girth. I lost just over an inch of that girth with the implant and a 1/4" in length . I think the loss of girth was do to me using trimix injections for over 12 years. I notice the increase in girth over that time. I am thrilled with my flaccid size and very happy overall with my implant.DSCN1699.JPGDSCN1700.JPGDSCN1688.JPG

Great looking setup Happs.......so good for everyone on here that you posted pics.....

[Lester33]

Looks great so glad for you we were done about the same time. I am 100% happy with my results too.

[William8]

Great Thread. Thanks for the info.

Is the stretch test "bone press" or just the base of shaft to the tip?

Thanks

[Happy Toy]

Great Thread. Thanks for the info.

Is the stretch test "bone press" or just the base of shaft to the tip?

Thanks

They did not do a stretch test on me but think they just pull the head as far as you can stand an measure from the base to the tip. When I measure my erection I do a "bone press" which I think is a standard way of measurement of erection length.
Hope this helps, Andy

[Lost Sheep]

Great Thread. Thanks for the info.

Is the stretch test "bone press" or just the base of shaft to the tip?

Thanks

They did not do a stretch test on me but think they just pull the head as far as you can stand an measure from the base to the tip. When I measure my erection I do a "bone press" which I think is a standard way of measurement of erection length.
Hope this helps, Andy

To measure an unimplanted penis while flaccid:

Press a blunt stick (ruler) into the pubic fat pad (just above your penis) and stretch the tip of your penis as much as you can and mark on the stick (ruler) for the length.

The stick (ruler) should be blunt (and flat) so you don't hurt your skin when you press to your pubic bone. Pressing to the bone will allow you to be consistent each time you measure.

To measure an erect penis, the procedure is the same, but without pulling on the head of the penis. Just hold the penis' shaft against the stick(ruler).

[William8]

Thank you both for the reply

[DougAnd]

William,
A good bone pressed measurement is supposed to equal a hard erection. Don't know never had a hard erection to try it on.

[Geronimo]

Another way to measure is to use a Taylors Tape, soft and flexable, used for length and girth.