Page 1 of 2

Process for starting injectables

Posted: Thu Jun 14, 2018 6:06 pm
by Robert-CA
My urologist had me come into the office and showed me how to do the injection with a minimal dose. He then told me to increase the dose in small increments until I was able to achieve a satisfactory erection. (Let's call this process A)

I have heard from others that their doctors had them come back to the office for repeated injections until they found the right dosage. (Process B)

So I am curious about other guys who use injectables. Did your doctor use Process A or B?

Re: Process for starting injectables

Posted: Thu Jun 14, 2018 7:40 pm
by Reggieman
Doc injected me in his office with 30 units of Bimix. Too much so they had to draw blood from my penis and gave me a shot in the penis to help it go flaccid. He sent home home with instructions to use 15 units. I found that I can use even less and get the same effect.

Re: Process for starting injectables

Posted: Thu Jun 14, 2018 8:39 pm
by once a writer
I had my initial injection in the office. After that I was on my own.

Re: Process for starting injectables

Posted: Thu Jun 14, 2018 9:10 pm
by bldoink
Process C. The doctor wrote me a script for Edex 10. I read and followed the instructions in the insert. At next appointment I told the doctor that it didn't work. He wrote me a script for Edex 20. I again followed insert instructions. It worked. It actually worked a bit too good and gave me some dick ache so I didn't inject the full ml the next time.

Re: Process for starting injectables

Posted: Fri Jun 15, 2018 4:08 pm
by Alanoc8
My Uro injected me in his office with 10 units. I just got a semi not hard enough for sex. He told me to increase it by 5 units until I reached a dose that would get me fully erect. I'm currently using 30 units and getting a great erection.

Re: Process for starting injectables

Posted: Fri Jun 15, 2018 5:19 pm
by tomas1
A

Re: Process for starting injectables

Posted: Fri Jun 15, 2018 6:45 pm
by keysdude
Robert-CA
My uro gave me my first shot, 5 units, and had me wait for reaction. 5 -25 min got major hard on. Sent me home with instructions and what to look for. Next appt 2 weeks later he had me self inject. No problem other than major case of nerves. That was it other than seeing him every few months just to ask how I've been doing with the injections.
Been injecting 1 -2 times a week for about 15 months or so. It's been working out fine. I did up the dosage to 8-10 units

Re: Process for starting injectables

Posted: Sat Jun 16, 2018 2:41 pm
by Bob1974
Process A... urologist gave me my 1st injection of 40/30/1 Trimix .01 or 10 units and did early in the afternoon(2pm) in case there was an issue. After 3.5 hours took 4 30mg Sudafed and put ice on it and by 7pm I was good. Still trying to find right dosage as 4 units still seems too strong for me.

Re: Process for starting injectables

Posted: Sat Jun 16, 2018 2:45 pm
by Larry10625
Robert-CA wrote:My urologist had me come into the office and showed me how to do the injection with a minimal dose. He then told me to increase the dose in small increments until I was able to achieve a satisfactory erection. (Let's call this process A)

I have heard from others that their doctors had them come back to the office for repeated injections until they found the right dosage. (Process B)

So I am curious about other guys who use injectables. Did your doctor use Process A or B?



A for me.

Larry

Re: Process for starting injectables

Posted: Sat Jun 16, 2018 10:22 pm
by graymare
A for me. But when I got my initial injection, they gave me a porn magazine and told me to look through that for 10 minutes. Then they came back to do a penile color doppler ultrasound. The porn was a waste of their money.