Pump to get chubby before injection
Posted: Tue Mar 05, 2024 1:42 pm
Can someone recommend a good pump to use to plump before injection.
FrankTalk.org
support group helping men deal with Erectile Dysfunction.
https://www.franktalk.org/phpBB3/
Pump to get chubby before injection
Page 1 of 2
Re: Pump to get chubby before injection
Posted: Wed Mar 06, 2024 4:03 pm
I would think a cheap VED from Amazon would work well for just getting it ready for a trimix injection….
Re: Pump to get chubby before injection
Posted: Wed Mar 06, 2024 4:18 pm
Burt-Man wrote:I would think a cheap VED from Amazon would work well for just getting it ready for a trimix injection….
BUT...
IMHO, The use of a VED prior to an injection could cause a hematoma.
Only a suggestion, check with the doctor that prescribed the Tri-Mix.
stmfttr
Re: Pump to get chubby before injection
Posted: Wed Mar 06, 2024 5:33 pm
stmfttr wrote:IMHO, The use of a VED prior to an injection could cause a hematoma.
I think that would be more of an issue if used after the injection.
Re: Pump to get chubby before injection
Posted: Wed Mar 06, 2024 8:24 pm
bldoink wrote:stmfttr wrote:IMHO, The use of a VED prior to an injection could cause a hematoma.
I think that would be more of an issue if used after the injection.
Yes, that too.
Re: Pump to get chubby before injection
Posted: Wed Mar 06, 2024 9:21 pm
I was told it was ok to do before injecting and it would open things up in the penis and help the trimix spread out and work.
Re: Pump to get chubby before injection
Posted: Thu Mar 07, 2024 11:57 pm
Which cheap VED on Amazon?
Re: Pump to get chubby before injection
Posted: Fri Mar 08, 2024 12:03 am
Which cheap VED on Amazon?
Re: Pump to get chubby before injection
Posted: Wed Mar 13, 2024 11:38 am
I just bought a Adorime pressure pump off Amazon. Has worked great for the pre-injection plump up. Going to inject for my 3rd time today and hopefully will not repeat the first two disasters now that I have the pump.
Re: Pump to get chubby before injection
Posted: Wed Mar 13, 2024 1:36 pm
Budward. Good luck.
I did injection number 5 yesterday and pumped up beforehand and it seemed to help a lot. I popped on a ring, so I would not lose my size while I was searching for my target area. How much to pump up is sort of a question. I went to about half way to full. I tend to get this fear like it will pop like a balloon full of water when I put in the needle, but of course I know it will not.
I’ve had 3 successful injections on my right side and both attempts on the left side have been failures, with noticeable pain and soreness. Not sure why, but I’m hoping when I try the left side again after pumping it up, it will be more successful.
Don’t give up. Yesterday’s event felt just about as close to what it felt like it was before my RP. It was great.
By the way, when I was searching for a pump, a lot of the ones with a gauge registered the pressure in MBAR instead of Lbs. I believe that 200 MBAR is equal to 4 or 4.5 lbs of pressure, which you probably don’t want to exceed.
Anyone else have an opinion on what the maximum safe pressure would be in MBAR?
I did injection number 5 yesterday and pumped up beforehand and it seemed to help a lot. I popped on a ring, so I would not lose my size while I was searching for my target area. How much to pump up is sort of a question. I went to about half way to full. I tend to get this fear like it will pop like a balloon full of water when I put in the needle, but of course I know it will not.
I’ve had 3 successful injections on my right side and both attempts on the left side have been failures, with noticeable pain and soreness. Not sure why, but I’m hoping when I try the left side again after pumping it up, it will be more successful.
Don’t give up. Yesterday’s event felt just about as close to what it felt like it was before my RP. It was great.
By the way, when I was searching for a pump, a lot of the ones with a gauge registered the pressure in MBAR instead of Lbs. I believe that 200 MBAR is equal to 4 or 4.5 lbs of pressure, which you probably don’t want to exceed.
Anyone else have an opinion on what the maximum safe pressure would be in MBAR?