Looking for a replacement cylinder for my pump

Specific talk about pumps: Questions, hints, recommendations, etc.

Moderator: Larry10625

Cajun Jeff
Posts: 795
Joined: Sat Aug 01, 2009 11:44 pm
Contact:

Looking for a replacement cylinder for my pump

Postby Cajun Jeff » Wed Oct 31, 2018 5:15 pm

The one that came with my pump I think is 2 in. I need one a bit smaller this one keeps trying to suck in a nut. Not fun. Ouch. It’s elect and fits on the top of the tube.

Any help would be appreciated.

60s_surfer
Posts: 14
Joined: Mon Jul 30, 2018 1:42 pm

Re: Looking for a replacement cylinder for my pump

Postby 60s_surfer » Thu Nov 01, 2018 2:31 pm

I know of two possible solutions that don't require a new cylinder. On the UandMeTime Web site, there is a disk with a hole in the middle that fits over your erection and then the cylinder pushes the flat part of the disk up against your abdomen. You need to lubricate both sides of the disk to get a good seal. The other possibility depends on the exact size of your cylinder. The Timm Medical Web site has an insert that goes inside the cylinder to reduce the inner diameter. I believe it is for a cylinder with 2 inches inside diameter. Timm Medical sells the Osbone pump and constriction rings.
71 years old in 2018; married 49 years. ED since 2001. PD5 inhibitors (Viagra, etc.) worked with increasing dosages until side effects got too bad by 2017. Now using Trimix injections. Delayed ejaculation has been a continuing problem since 2012.

Cajun Jeff
Posts: 795
Joined: Sat Aug 01, 2009 11:44 pm
Contact:

Re: Looking for a replacement cylinder for my pump

Postby Cajun Jeff » Thu Nov 01, 2018 8:04 pm

Thanks

dtwarren1942
Posts: 1488
Joined: Wed Oct 27, 2010 7:58 pm
Location: Jersey Shore

Re: Looking for a replacement cylinder for my pump

Postby dtwarren1942 » Sun Nov 04, 2018 2:54 pm

If your pump uses a standard male connector, LeLuv offers a decent quality cylinder with a wide base rim for comfort for about $30.

Cylinder sizing according to,LAPump

Girth —---> Cylinder Diameter
3.50 to 4.50* --> 1.50
4.75 to 5.25* --> 1.75
5.50 to 6.00* --> 2.00
6.25 to 6.75* --> 2.25
7.00 to 7.50* --> 2.50
7.75 to 8.25* --> 2.75
Age 76
Diabetic
Pumping
Started Trimix injections 8/'11

JimStars
Posts: 798
Joined: Sun Jan 24, 2010 2:41 pm

Re: Looking for a replacement cylinder for my pump

Postby JimStars » Mon Nov 05, 2018 11:26 pm

CJ,

The main thing is, ALWAYS be holding onto your nuts when pumping -- stretching scrotum down a bit -- keeping it that way until you slip on the rings. If not using rings and just keeping suction for a while -- well you will just have to judge if they be sucking back into cylinder. With an electric pump it is pretty easy to do pump and hold em with other hand.

J
RP 2008 ... MUSE 2008-9 .. TriMix Gel 2009 .. Trimix 2009-2015 ... PGE-1 2016 Onward. All worked.

Cajun Jeff
Posts: 795
Joined: Sat Aug 01, 2009 11:44 pm
Contact:

Re: Looking for a replacement cylinder for my pump

Postby Cajun Jeff » Wed Nov 07, 2018 9:53 pm

Will try that. What I have done is start with low suction. Get the blood moving. Then add more pressure. After several rounds I can get to full suction. What I am searching far is a cylinder that does not allow girth but pulls for length.

dtwarren1942
Posts: 1488
Joined: Wed Oct 27, 2010 7:58 pm
Location: Jersey Shore

Re: Looking for a replacement cylinder for my pump

Postby dtwarren1942 » Thu Nov 08, 2018 8:54 pm

I have a 2.25” cylinder which I use occasionally, but it does invariably suck in my right Testicle after five minutes or so. I recently carefully slipped on a doubled over 1/2 inch wide elastic band over my balls, Just under the base of my shaft. I used a lot of lube on my balls and the band. And, it prevent my ball from being sucked up.
Age 76
Diabetic
Pumping
Started Trimix injections 8/'11

Cajun Jeff
Posts: 795
Joined: Sat Aug 01, 2009 11:44 pm
Contact:

Re: Looking for a replacement cylinder for my pump

Postby Cajun Jeff » Fri Nov 09, 2018 10:15 pm

No exactly what you Man about 1/2 inch elastic band. Where do you get that?

FishingTime67
Posts: 350
Joined: Fri Jul 13, 2018 11:58 pm

Re: Looking for a replacement cylinder for my pump

Postby FishingTime67 » Fri Nov 09, 2018 10:21 pm

Cajun Jeff wrote:Will try that. What I have done is start with low suction. Get the blood moving. Then add more pressure. After several rounds I can get to full suction. What I am searching far is a cylinder that does not allow girth but pulls for length.


Just use your hands and grab a squeeze real hard...lol.. jk
I'm 51 new implant in Jan. 2018 with Titan one 24 cm no RTE,had issues with tubbing and fluid gathered around reservoir which cause deflation issues. Tubbing got kinked. Had total replacement with AMS CX 24cm 3rtes
Size 7 in. girth 6 erect

dtwarren1942
Posts: 1488
Joined: Wed Oct 27, 2010 7:58 pm
Location: Jersey Shore

Re: Looking for a replacement cylinder for my pump

Postby dtwarren1942 » Sat Nov 10, 2018 4:52 pm

Cajun Jeff wrote:No exactly what you Man about 1/2 inch elastic band. Where do you get that?


1/2 inch is a standard size rubber/elastic band available at stationary section of any big box store or Staples. You can probably get a bag of 100 for about $1.
Age 76
Diabetic
Pumping
Started Trimix injections 8/'11


Return to “Pumps”

Who is online

Users browsing this forum: No registered users and 5 guests