Gauge or no gauge

Specific talk about pumps: Questions, hints, recommendations, etc.
bobsk8
Posts: 6
Joined: Sat Apr 11, 2026 6:38 pm

Gauge or no gauge

Postby bobsk8 » Wed Apr 22, 2026 10:51 am

I got a Encore VED two weeks ago and it works great. The one thing that bothered me is that it has no gauge, which is similar to just about every medical grade VED that I have seen on line. I decided to order a LeLuv unit with a gauge, just to compare the two as far as what the different pressures feel like. I used -5hg as the max pressure on the gauge. I was surprised to find that it this seemed to feel like more pressure than I was feeling on the Encore unit, so apparently I was well in the safe zone with the Encore unit just using how it felt as a guide line for when to stop pumping.

John Dday
Posts: 108
Joined: Thu Sep 05, 2024 8:30 pm

Re: Gauge or no gauge

Postby John Dday » Wed Apr 22, 2026 4:26 pm

I use a Bathmate VED with measurements, which are helpful to see that you are indeed slightly stretching. While pumped, I also do my daily keegle exercises ( prostatectomy ), shave etc. It is a gentler pump than air vacuums, and nowhere as messy. It did take a bit of getting used to, as it takes 3 refills.
1955. I have had ED for years. We were planning to go for a Rigi10 in October 2024. Life got in the way (heart attack & stent), so we are now going for injections as a fill-in. 9/2025 More life roadblocks with prostate Cancer:((

RJ_in_Pa
Posts: 159
Joined: Tue Oct 17, 2023 4:34 pm
Location: Pa

Re: Gauge or no gau

Postby RJ_in_Pa » Fri May 01, 2026 10:20 am

I bought the same device (Encore) and was concerned about it not having a gauge. I bought a gauge from LeLuv and installed it on the upper side of the tube.

If you have a hand power drill and a set of drill bits, it’s fairly easy. As I remember, I think the hole size was 3/8, but I would strongly recommend that you take a piece of scrap wood, drill a hole in it and do a test fit. The treads of the gauge will self tap as you screw it in.

Once you do that and are confident that you have the right size drill bit, find a good spot on the tube where it is easy to read while pumping and drill a VERY SMALL HOLE that is close to be being as perpendicular to the tube as possible. Then us a little larger bit and drill again. Do this until you get to the hole size of your test hole. I was afraid if I started with the largest bit, it might split the plastic, if you know what I mean.

I did not need to put anything on the treads of the gauge to prevent air leaking. I just very carefully “screwed it into the hole” being sure not to screw it in “cock-eyed” (so to speak :D )

Good luck (if you choose to try it)! I also added lines to show me what length I’m at.

I tried to add a pic, but it said it was too large.
65, Radical Prostatectomy in 2023, pills did nothing. Used Trimix with great success, but now trying regain ability to get natural erections as I did prior to RP surgery. So far, able to have PIV sex with a C ring.

User avatar
GoodWood
Posts: 1597
Joined: Sun Jun 16, 2019 1:07 pm

Re: Gauge or no gauge

Postby GoodWood » Fri May 01, 2026 11:22 am

I used a pump each morning for months leading up to surgery. Mine didn’t have a gauge. I didn’t worry about it. I was after a feeling of stretch and tension but not pain. If it hurts it’s too much regardless of what the gauge says.
If there is edema or bruising it was too much pressure regardless of what the gauge said.
57yo, NYC. ED started at 40. Pills, then shots for 10 years. 24cm Coloplast Titan XL w/classic pump by Dr Eid 3/25/2025. Will meet for show & tell.
Implant journal: [url] viewtopic.php?f=6&t=26225[/url]


Return to “Pumps (Vacuum Erection Device)”

Who is online

Users browsing this forum: ClaudeBot and 51 guests