Search found 1436 matches

by Agfa13
Sun Jul 05, 2020 7:18 pm
Forum: Implants
Topic: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.
Replies: 459
Views: 61117

Re: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.

75%- 80%??? Shit, I have been doing this too aggressively, but hey, I want this ASAP!
Will try this, then report back. Tks for the feedback.
by Agfa13
Sun Jul 05, 2020 10:29 am
Forum: Implants
Topic: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.
Replies: 459
Views: 61117

Re: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.

Hehehe...you know, you can say 'fuck' on here:)! Doing my therapy as I type this. Have a question about my pumping. When I initially pump, about 25 pumps now up from 20, the 1st few minutes are hurting. Like enough so I want to deflate ASAP! Tried to get my mind off of the hurt, but it is hard, no p...
by Agfa13
Sat Jul 04, 2020 4:27 pm
Forum: Implants
Topic: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.
Replies: 459
Views: 61117

Re: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.

You mean these past 4 months of no fucking was not rest??? Self luv is not resting? Damn, you are ruff :lol: ! Got a blowjob yesterday, it was wonderful! I did not cum, but damn, this is a milestone for me in recovery, lol. Too afraid to fuck right now, but will try it at end of month. Laying off di...
by Agfa13
Wed Jul 01, 2020 7:12 pm
Forum: Implants
Topic: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.
Replies: 459
Views: 61117

Re: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.

Hehehe...NOW I can piss with a hardon!!! Never done that(just by depressing button)...how long will it take to drain? Now, as for that TRY....my whole dick, or just the head (pulling back foreskin). As for the whole dick...that is a challenge. 3 days is my max (except for surgery, and that was almos...
by Agfa13
Wed Jul 01, 2020 8:56 am
Forum: Implants
Topic: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.
Replies: 459
Views: 61117

Re: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.

I just pump right now, no VED. I have tried the VED, but it has to be mood thing for me at this point. Pumping is painful. Inside of dick is being stretched and I really can't do anything else. Unlike *most* guys on here, my situation will take a boatload longer to get to where they are at:( (pity p...
by Agfa13
Tue Jun 30, 2020 5:48 pm
Forum: Implants
Topic: Dont want to pump in front of her
Replies: 47
Views: 6692

Re: Dont want to pump in front of her

Not voluntarily. Long story, but got an infection, so had to replace it.
by Agfa13
Mon Jun 29, 2020 10:16 pm
Forum: Implants
Topic: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.
Replies: 459
Views: 61117

Re: Agfa13- My journal, 3-piece, then 1-piece, back to 3-piece.

Well guys, actually tried fucking ass today...I lasted about 8 seconds before I said 'no mas'. The area right behind the head is sensitive as heck and self luv is about the only thing I can handle right now :x
by Agfa13
Mon Jun 29, 2020 10:13 pm
Forum: Implants
Topic: Dont want to pump in front of her
Replies: 47
Views: 6692

Re: Dont want to pump in front of her

Yes, practice makes pumping easier/faster.
Just started pumping yesterday with one hand. Grab pump with your dominant hand. MAKE SURE to grab pump itself like a pair of dice, fingers holding pump right below valve(s) so it does not slip.
by Agfa13
Sat Jun 27, 2020 9:13 am
Forum: Implants
Topic: Sharp edge/corner when the cylinders are deflated/bent
Replies: 16
Views: 2442

Re: Sharp edge/corner when the cylinders are deflated/bent

Indusvalley, I think everyone has dogears, it is just a matter of degrees, meaning that if you are hung in a flaccid state, you probably won't have much, if any. If you are on the smaller side, more than likely, you will have them. This is because the tubing, if you look at vids of implants, is bigg...
by Agfa13
Fri Jun 26, 2020 10:02 pm
Forum: Implants
Topic: Sharp edge/corner when the cylinders are deflated/bent
Replies: 16
Views: 2442

Re: Sharp edge/corner when the cylinders are deflated/bent

Hehehe...glad to hear that. I was going to try it, but I guess I will just change it up sooner or later to something that feels right to me.

Go to advanced search