Search found 830 matches
- Wed May 15, 2019 5:36 pm
- Forum: Injections
- Topic: BioFreeze (cold spray) Before Injecting?
- Replies: 13
- Views: 5234
Re: BioFreeze (cold spray) Before Injecting?
For me the pinch at the skin is not usually the problem. It is when you hit a sensitive spot (nerve?) on the way towards the tunica that can take your breath away for a second til you probe on thru it. I don't think any numbing will help with that. But that's just because I dig in slowly -- I don't ...
- Wed May 15, 2019 5:31 pm
- Forum: Injections
- Topic: Your Results Using a Mirror to Inject Trimix?
- Replies: 8
- Views: 1754
Re: Your Results Using a Mirror to Inject Trimix?
HT,
For me there is zero curving. But I have been using mostly just PGE-1 -- not Trimix -- for all those years. It is much cheaper (and supposedly plain PGE-1 might have less effect towards peyronies than Trimix).
No one really seems to know exactly what causes Peyronies anyways).
J
For me there is zero curving. But I have been using mostly just PGE-1 -- not Trimix -- for all those years. It is much cheaper (and supposedly plain PGE-1 might have less effect towards peyronies than Trimix).
No one really seems to know exactly what causes Peyronies anyways).
J
- Tue Apr 30, 2019 10:15 pm
- Forum: Injections
- Topic: Your Results Using a Mirror to Inject Trimix?
- Replies: 8
- Views: 1754
Re: Your Results Using a Mirror to Inject Trimix?
HardT, Although I have never had your NoSeeEm problem -- flat stomach, lucky me -- what I always do before injecting is to really plump up. Maybe that is easier said that done .. or even described .. but for me it requires repeatedly squeezing at the base, milk up a bit and then give a few good wagg...
- Fri Jan 04, 2019 11:23 pm
- Forum: Injections
- Topic: Why are some injecting and pulling some blood out?
- Replies: 14
- Views: 3021
Re: Why are some injecting and pulling some blood out?
I never aspirate, but will usually see a tiny drop of blood backflow anyways when the needle is in the corpus cavernosum. And as far as hitting a vein or artery (and needle stops inside) .. that sounds just too unlikely. You can likely go THRU an artery or vein and out the other side. Also, do not d...
- Fri Jan 04, 2019 11:03 pm
- Forum: Implants
- Topic: Anyone Here Used MUSE? Is it Better than Implants?
- Replies: 16
- Views: 3325
Re: Anyone Here Used MUSE? Is it Better than Implants?
I have used MUSE in the past and it worked OK .. but usually, if it was a correct dose for a good erection it was also enough for an annoying ache. Yeah and crazy expensive. As a do-it-yourself alternative, you could try Misoprostal (200 mcg PGE-1) pills. Crushed and powdered and mixed with water an...
- Tue Nov 20, 2018 6:22 am
- Forum: Injections
- Topic: Trimix & 31 gauge needle
- Replies: 13
- Views: 4206
Re: Trimix & 31 gauge needle
I had used 31gauge x 5/16" (8mm) for a while but always thought they were a little too flimsy. Not that they would bend and break (try breaking one off by bending -- takes a dozen bends at least) but WAS concerned about bending and then glancing off the tough/smooth cavernosa. So I have since a...
- Mon Nov 05, 2018 11:26 pm
- Forum: Pumps (Vacuum Erection Device)
- Topic: Looking for a replacement cylinder for my pump
- Replies: 11
- Views: 3194
Re: Looking for a replacement cylinder for my pump
CJ, The main thing is, ALWAYS be holding onto your nuts when pumping -- stretching scrotum down a bit -- keeping it that way until you slip on the rings. If not using rings and just keeping suction for a while -- well you will just have to judge if they be sucking back into cylinder. With an electri...
- Sat Oct 27, 2018 3:29 pm
- Forum: Injections
- Topic: Questions about results
- Replies: 16
- Views: 3460
Re: Questions about results
Falcon, You might be able to eek a little more length (and def more girth) if you add on a restriction ring of some sort. But that depends on if your current erection is already 100% or is somewhat less... If somewhat less, then restriction will boost it a bit -- plus add definition due to better EQ...
- Sat Oct 27, 2018 3:08 pm
- Forum: Pumps (Vacuum Erection Device)
- Topic: What size and tension Osbon ring?
- Replies: 22
- Views: 6146
Re: What size and tension Osbon ring?
Similar to DT ... my girth is around 5.5 or more. I use: Beige - Large; Standard Tension Ring (A). Fits all ErecAid® models. Inner Diameter - 22mm (0.875 in.) and Pink - Large; High Tension Ring (B). Fits all ErecAid® models. Inner Diameter - (22mm) 0.875 in. Use those two stacked together. Sometime...
- Thu Oct 11, 2018 6:36 pm
- Forum: General Discussion
- Topic: Asking if anyone has tried this...
- Replies: 21
- Views: 8275
Re: Asking if anyone has tried this...
OK ... finally got a picture of the applicator ... including an 'exploded' view.
3-d Printer fans have at it!
J
[img]applicator.jpg/img]
3-d Printer fans have at it!
J
[img]applicator.jpg/img]